How to Fix "CHKDSK Is Not Available for RAW Drives"
In this article
"CHKDSK is not available for RAW drives" means your file system is corrupted or missing, so Windows can't identify the drive as NTFS, FAT32, or exFAT. CHKDSK needs a recognizable file system to repair, so it can't run. Your files are still on the drive: do not format. In most cases the data is recoverable.
- Don't format or run CHKDSK: both can overwrite recoverable data
- If the drive is silent and healthy: try TestDisk or PhotoRec to a separate drive
- If it clicks, beeps, or software fails: stop and use professional hard drive data recovery
When Windows tells you "CHKDSK is not available for RAW drives," it means your drive's file system is gone. Corrupted, unreadable, wiped out. Windows can't even recognize it as NTFS, FAT32, or exFAT anymore. It sees raw, unformatted storage. The data is almost certainly still there on the platters or flash chips. But you can't get to it through normal means. The good news? In most cases, the files can be recovered. The bad news? Running the wrong command right now could make things permanently worse.
This guide walks you through exactly what happened to your drive, what your options are, and when you should stop trying to fix it yourself.
What Does "RAW" Actually Mean?
Every storage device needs a file system. Think of it like a table of contents in a book. NTFS, FAT32, exFAT, HFS+, APFS. These file systems tell your operating system where each file starts, where it ends, what it's called, and which folder it belongs to.
When a drive shows as "RAW," that table of contents is damaged or missing entirely. Windows looks at the drive, tries to read the file system header, and comes back with nothing it can understand. So it labels the entire partition as RAW.
Your files are still physically stored on the drive. The magnetic patterns on a hard drive's platters don't just vanish because the file system got corrupted. Our dedicated guide on recovering data from a RAW drive walks through the full recovery process. Same goes for flash storage. The actual data blocks are still there. What's missing is the map that tells Windows how to find them.
You'll usually notice this when:
- Windows asks you to "format the disk before you can use it"
- The drive shows up in Disk Management as RAW with no file system listed (it may also show as "Disk Unknown Not Initialized")
- You try to open the drive and get "The volume does not contain a recognized file system"
- File Explorer shows 0 bytes used and 0 bytes free
- CHKDSK throws the "not available for RAW drives" error
All of these symptoms point to the same root problem. The file system metadata is unreadable.
Why CHKDSK Fails on RAW Drives
CHKDSK (Check Disk) is a Windows utility designed to find and fix file system errors. It works by scanning the file system structures, looking for inconsistencies, fixing cross-linked files, recovering orphaned clusters. Standard maintenance stuff.
But here's the thing. CHKDSK needs a file system to work with. It's built to repair NTFS and FAT32. When the file system is so damaged that Windows can't even identify what type it is, CHKDSK has nothing to latch onto. It can't repair what it can't read.
That's why you see "CHKDSK is not available for RAW drives." It's not a bug. It's CHKDSK being honest. The tool simply wasn't designed for this situation.
People often try running chkdsk D: /f or chkdsk D: /r hoping it'll fix things. It won't. Not when the drive is RAW. Those switches tell CHKDSK to fix errors (/f) or locate bad sectors and recover readable data (/r). Both require an existing, recognizable file system to operate on.
Common Causes of RAW Drive Errors
Drives don't go RAW for no reason. Something happened. Understanding what went wrong helps you decide the right recovery approach.
1. Sudden Power Loss or Unsafe Removal
See also external hard drives not showing up in Windows. You pull out a USB drive without ejecting it. The power goes out while Windows is writing to the disk. A laptop battery dies mid-transfer. Any of these can corrupt the Master File Table (MFT) on NTFS drives or the File Allocation Table on FAT32 drives. One corrupted sector in the wrong spot and the whole file system becomes unreadable.
2. Bad Sectors in Critical Areas
Hard drives develop bad sectors over time. It's normal wear. But if bad sectors land on the boot sector, partition table, or MFT, the drive can flip to RAW status overnight. You might have been using the drive fine yesterday. Today it's RAW. That's because the specific sector holding critical file system data finally gave out.
3. Virus or Malware Damage
Some malware intentionally corrupts partition tables or file system headers. Ransomware variants have been known to encrypt the MFT while leaving the actual file data untouched. The result? Your drive shows as RAW even though the files themselves are still intact underneath.
4. Failed Format or Partition Operation
Interrupted format operations are brutal. If you started formatting a drive and it got interrupted partway through, you end up in no-man's-land. The old file system was partially overwritten, the new one never finished writing. RAW is what's left.
5. Failing Drive Hardware
Sometimes the drive itself is dying. Degrading read/write heads on a hard drive. A failing controller board. Bad NAND blocks on an SSD. If the drive can't reliably read its own file system structures, Windows sees garbage data and reports RAW. This is the scenario where knowing the signs of a failing hard drive early can save your data.
6. Partition Table Corruption
The partition table (MBR or GPT) tells Windows where each partition starts and what type it is. If that table gets corrupted, Windows might see the partition but can't identify its file system. Disk management tools, dual-boot installers, and cloning software gone wrong are common culprits here.
| Cause | Severity | DIY Recovery Chance |
|---|---|---|
| Unsafe removal / power loss | Low to Medium | High (software usually works) |
| Bad sectors in file system | Medium | Medium (depends on extent) |
| Malware / ransomware | Medium to High | Medium (if data isn't encrypted) |
| Interrupted format | Medium | Medium |
| Failing hardware | High | Low (needs professional tools) |
| Partition table corruption | Low to Medium | High (TestDisk often fixes this) |
Safe Fixes You Can Try at Home
Before you try anything, understand this: if the data on this drive matters to you, the safest move is to do nothing and send it to a professional. Every tool you run on a failing drive is a roll of the dice. That said, if the drive sounds healthy (no clicking, no grinding, no unusual noises) and you suspect the issue is file system corruption rather than hardware failure, these steps are relatively safe.
Step 1: Try a Different USB Port or Cable
How: Unplug the drive. Try a different USB port (preferably on the back of a desktop PC, directly on the motherboard). Try a different cable if it's an external drive. If it's a SATA drive inside a desktop, reseat the SATA data and power cables.
Step 2: Check Disk Management
How: Press
Windows + X, click "Disk Management." Find your drive in the list. Look at the partition. If it shows as RAW with the correct capacity, the drive hardware is likely fine and it's a file system issue. If the capacity is wrong or the drive doesn't appear at all, you probably have a hardware problem.
Step 3: Try TestDisk (Free, Open Source)
How:
- Download TestDisk from cgsecurity.org
- Run
testdisk_win.exeas Administrator - Select your drive, choose the partition table type (usually Intel/PC for MBR, EFI GPT for GPT)
- Select "Analyse" to search for partitions
- If TestDisk finds your original partition, select it and choose "Write" to restore the partition table
- Reboot and check if the drive is accessible
Step 4: Try Assigning a New Drive Letter
How: In Disk Management, right-click the partition and select "Change Drive Letter and Paths." Assign a new letter. If the drive was actually fine and just had a letter conflict, this fixes it instantly.
Step 5: Use Command Prompt to Convert RAW to NTFS (Risky)
convert command can sometimes repair a RAW NTFS partition. This only works in very specific scenarios where the NTFS structures are mostly intact but just enough is corrupted to trigger the RAW status.How: Open Command Prompt as Administrator. Type:
convert D: /fs:ntfs (replace D: with your drive letter).Warning: This doesn't always work on RAW drives. If the file system is too damaged, the command will fail. If you have critical data on the drive, skip this step and go straight to recovery software or professional help.
Using Data Recovery Software
If the fixes above didn't restore access, data recovery software is your next option. These tools work by scanning the drive sector by sector, looking for file signatures regardless of the file system status. They bypass the corrupted file system entirely and pull files directly from the raw data.
How Recovery Software Works on RAW Drives
Recovery software doesn't need the file system. It reads every sector on the drive and matches byte patterns against known file signatures. A JPEG always starts with FF D8 FF. A PDF starts with %PDF. A DOCX is actually a ZIP file with specific internal structure. By recognizing these signatures, recovery tools can reconstruct files even when the file system is completely gone.
The tradeoff? You'll probably lose file names and folder structure. Without the MFT or FAT, the software doesn't know what the files were called or where they were organized. You'll get folders named "Recovered_001" full of files named "file0001.jpg" and so on. But the data itself is there.
Recommended Recovery Tools
R-Studio is what we'd recommend for technical users. It's the closest thing to professional-grade recovery software available to consumers. It handles NTFS, FAT, exFAT, HFS+, and can work with drives showing as RAW. It costs about $80 for a license.
PhotoRec (free, from the same team that makes TestDisk) does excellent file carving. It's command-line based and not pretty, but it's effective and completely free. If you're comfortable with a text interface, it's a solid choice.
Recuva is easier to use but less powerful. Good for simple cases where the corruption isn't too severe. Free version available.
Step-by-Step: Recovering Files with PhotoRec
- Download PhotoRec from cgsecurity.org (comes bundled with TestDisk)
- Connect a second drive with enough free space for the recovered files
- Run
photorec_win.exeas Administrator - Select the RAW drive from the list
- Choose the partition (or "Whole disk" if no partitions are shown)
- Select the file types you want to recover (or leave all selected)
- Choose the destination folder on your second, healthy drive
- Let it run. This can take hours on large drives
If the drive has physical issues like bad sectors, recovery software will struggle. It'll either hang on the bad areas, produce corrupted output files, or miss data entirely. That's when you need professional help and professional data recovery tools that can handle sector-level failures.
When to Stop and Call a Professional
There's a point where DIY attempts do more harm than good. Knowing when to stop is just as important as knowing what to try. Here are the signs that you need to put the drive down and call someone.
The drive makes unusual sounds. Clicking, beeping, grinding, or repetitive ticking. These are mechanical failure sounds. The read/write heads are either crashed, stuck, or scraping against the platters. Every second this drive is powered on, the heads are potentially scratching irreplaceable data off the platters.
The drive gets extremely hot. A drive that's burning up after a few minutes of being connected usually has a failing motor or seized bearings. Running recovery software on it will just cook it further.
Recovery software freezes or hangs. If the software can't get past a certain point, the drive likely has a large cluster of bad sectors or a head that can't read certain areas. Professional tools can work around bad sectors by reading in reverse, skipping damaged zones, and adjusting head parameters. Consumer software can't do any of that.
The drive disappears and reappears. If the drive keeps disconnecting and reconnecting in Disk Management, the controller board or USB-to-SATA bridge is failing. Software recovery attempts on an unstable drive often result in incomplete, corrupted recoveries.
The data is irreplaceable. Family photos. Business records. A thesis you spent two years writing. If you can't afford to lose it, don't gamble with it. Professional recovery is an investment. Losing the data forever is the real cost.
What NOT to Do (Seriously)
We see the aftermath of bad advice constantly. Drives come into our lab worse than they needed to be. Don't make these mistakes.
Do NOT Format the Drive
When Windows pops up saying "You need to format the disk before you can use it," do NOT click Format. Formatting writes a new, empty file system over whatever's left of the old one. On a quick format, most data survives underneath. But on a full format, Windows zeros out every sector. Either way, you're making recovery harder, not easier.
Do NOT Run CHKDSK on a Failing Drive
Even if you somehow get CHKDSK to run (by converting the drive first), running CHKDSK on a drive with bad sectors is dangerous. CHKDSK can move data around, delete "orphaned" file entries, and reorganize structures. On a healthy drive, that's helpful. On a failing drive with physical problems, it can turn a recoverable situation into an unrecoverable one.
Do NOT Open the Drive
Hard drives need a clean environment to open. Not clean like "I wiped down the kitchen counter." Internal drive work needs a clean, filtered work area. One speck of dust on the platters causes a head crash. If you find a tutorial telling you to open your drive and "clean the heads," close that tab immediately. Learn more about what proper recovery looks like in our hard drive data recovery service page.
Do NOT Keep Power-Cycling a Clicking Drive
Every time you power on a clicking drive, the damaged heads attempt to initialize. They swing across the platters looking for the servo tracks. If the heads are bent or the platters are scored, each attempt grinds away more data.
Professional Data Recovery for RAW Drives
Most of the time, the data is fully recoverable. The process depends on what caused the drive to go RAW in the first place.
For logical failures (corrupted file system, damaged partition table, accidental format), we use professional forensic imaging tools to create a sector-by-sector clone of the drive first. Then we work on the clone. The original drive is never modified. Our tools can reconstruct NTFS, FAT32, exFAT, and HFS+ file systems from partial metadata. In most cases, we recover files with their original names and folder structure intact.
For head or platter work, the drive goes into our laminar-flow work area. We replace failed components, stabilize the drive, and image it onto healthy media before any data extraction begins. This is the part that can't be done at home, no matter what software you have.
Watch a real hard drive recovery from our lab:
What to Expect from the Process
- Diagnostic. Ship us the drive or drop it off. We evaluate it and tell you exactly what's wrong, what's recoverable, and what it'll cost. No surprises.
- Diagnostic and recovery charges. Our diagnostic costs $100 and is credited toward a successful recovery. Once diagnostics start it is non-refundable; donor drives and replacement parts that you approve are non-refundable once ordered, even if recovery fails. Recovery work starts after your approval of the estimate.
- Secure return. We deliver recovered data on a new external drive or via encrypted download. Your original drive is returned untouched.
If you've tried the software route and it didn't work, or if you'd rather not risk it, give us a call. We've been doing this for years and we've seen every flavor of RAW drive failure there is. Check our pricing page for transparent cost breakdowns, or just call and we'll walk you through it.
Frequently Asked Questions
Can CHKDSK fix a RAW drive?
No. CHKDSK requires an existing, recognizable file system (NTFS or FAT32) to operate. When a drive shows as RAW, the file system is too damaged or completely missing, so CHKDSK has nothing to work with. That's exactly why you see the "CHKDSK is not available for RAW drives" error. You need to use partition recovery tools like TestDisk or professional data recovery services instead.
Is my data lost if my drive shows as RAW?
Almost certainly not. RAW status means the file system metadata is corrupted or unreadable. Your actual files, photos, documents, and videos are still physically stored on the drive. They just can't be accessed through normal file browsing because the "map" that tells Windows where everything is stored got damaged. Data recovery software or professional services can typically retrieve the files by reading the drive at a sector level.
Why did my external hard drive suddenly become RAW?
Pulling the USB cable while Windows was still writing data can corrupt the file system in an instant. Other causes include power surges, bad sectors developing in critical file system areas, malware, or the drive starting to physically fail. If the drive was working fine yesterday and is RAW today with no unusual sounds, it's most likely file system corruption from an improper disconnection.
Can I format a RAW drive to fix it?
Formatting will make the drive usable again, yes. But it will also make your existing data much harder to recover. A quick format writes a new, empty file system over the old one. Your data still exists underneath for a while, but the more you use the drive after formatting, the more original data gets overwritten permanently. If you need the data on the drive, do NOT format it. Recover the data first, then format. We cover this in detail in our guide on recovering data from a formatted hard drive.
How much does professional RAW drive recovery cost?
It depends on what caused the drive to go RAW. Logical recoveries (file system corruption, accidental format, partition table damage) typically cost less than physical recoveries. Physical recoveries requiring work in a clean, filtered area (head replacements, platter extraction, motor repair) cost more because of the specialized equipment and parts required. At MDrepairs, the diagnostic precedes your approval of a recovery estimate. Visit our pricing page for detailed breakdowns.
Is it safe to use free data recovery software on a RAW drive?
If the drive is mechanically healthy (no clicking, grinding, or beeping sounds), free tools like PhotoRec and TestDisk are generally safe to use. They read the drive without modifying it. The key rules: never install the software onto the RAW drive, never save recovered files onto the RAW drive, and stop immediately if the drive starts making unusual sounds or the software freezes repeatedly. If the drive has any physical symptoms, software recovery can make things worse.
What's the difference between RAW and unallocated?
A RAW partition is one that Windows detects but can't read the file system on. The partition entry exists in the partition table, but the file system data is corrupted. An unallocated space means there's no partition defined for that area of the drive at all. Both can result from corruption, but they require different recovery approaches. RAW partitions often respond well to file recovery software. Unallocated space may need partition table reconstruction with tools like TestDisk first.
What “CHKDSK Is Not Available For RAW Drives” Means
The message “CHKDSK is not available for RAW drives” means Windows cannot recognize a valid file system on that volume. It does not necessarily mean the drive was intentionally formatted as RAW, and it does not automatically mean the files are gone. It means CHKDSK cannot find a normal NTFS, exFAT, or FAT structure to verify, so it refuses to run.
CHKDSK is a file system repair tool. It expects to see recognizable metadata: boot sector, file tables, bitmap records, directories, and allocation information. When those structures are missing, corrupted, unreadable, or blocked by hardware failure, Windows labels the volume RAW. At that point, CHKDSK has no stable map to repair. Trying to force repairs with formatting, partition tools, or repeated scans can overwrite the same metadata needed to rebuild the file system later.
RAW can happen for several reasons. On hard drives, bad sectors near the beginning of the volume can make the file system disappear even if most user data is still present. On SSDs and flash drives, controller faults, corrupted translation tables, or unsafe unplug events can produce the same symptom. On external drives, a failing USB bridge can also interrupt reads and make Windows think the file system is gone.
The correct workflow depends on the cause. If the storage device is healthy and only the partition information is damaged, recovery software may be able to scan the volume and rebuild files. If the device is unstable, software scans are risky because they read aggressively for hours and may push the drive further into failure. In lab work, we image the media first, skip and return to weak areas intelligently, then reconstruct the file system from the clone.
If Windows asks to format the RAW drive, cancel it. Formatting creates a new file system, which can make the old one harder to reconstruct. If the files are important, stop using the drive and avoid CHKDSK, diskpart clean, initialization, and write based repair utilities. Our hard drive recovery workflow is built around preserving the original media before any logical repair is attempted.
Can CHKDSK fix a RAW partition?
No. CHKDSK needs a recognizable file system before it can repair anything. When Windows marks a partition RAW, CHKDSK cannot safely interpret the structure, so it stops. The right approach is to determine whether the problem is logical corruption, bad sectors, failing electronics, or flash translation damage, then recover from a copy whenever possible.
Should I format a RAW drive and then recover the files?
Do not format first if the files matter. A quick format may still leave some data behind, but it writes new file system structures over old evidence. A full format or SSD TRIM related event can be much worse. Recover the data first, then format or replace the drive only after the files are secured.
How MDrepairs can help
Real cases like this come through our New Jersey lab every week. If you are dealing with one now, start here.
