Sony A7 / A1 CFexpress Card Error: Pro Recovery Guide
Our founder and lead technician, Joseph Montanti, handles cases personally.
Stop recording and do not format the affected card. If it is physically sound and reads reliably, logical recovery from an image may help. Hardware failures and unstable reads need specialist assessment. Neither an error message nor the first hour after failure establishes a fixed recovery percentage.
On this page
CFexpress Type A vs Type B vs XQD vs UHS-II SD
Sony is the only major manufacturer that ships CFexpress Type A cards. Everyone else (Canon, Nikon, Panasonic, RED, Blackmagic) uses Type B. The two formats are physically incompatible and electrically different, even though they share the CFexpress name. This matters for recovery because the readers, the controllers, and even the lab tools differ.
Here's the quick technical breakdown that matters when you're talking to a recovery lab.
| Format | Bus | Sony Bodies That Use It |
|---|---|---|
| CFexpress Type A | PCIe 3.0 x1 (NVMe) | A1, A1 II, A7 IV, A7 V, A7S III, A9 III, FX3, FX30, FX6, FX9 |
| CFexpress Type B | PCIe 3.0 x2 (NVMe) | Not used by Sony cameras (used by Nikon, Canon R5/R3) |
| XQD (legacy) | PCIe 2.0 x2 | Older Sony FS5, FS7 cinema bodies. CFexpress Type B is backward compatible. |
| UHS-II SD | UHS-II bus (not PCIe) | Slot B on dual-slot A7 and A1 bodies. Slower but cheaper. |
| SxS (broadcast) | PCIe 2.0 x1 | Older Sony broadcast bodies. Different protocol entirely. |
Sony's CFexpress Type A is physically smaller than Type B (about the size of an SD card versus the bigger Type B form factor) and uses a single PCIe lane instead of two. That gives Type A roughly 800 MB/s sustained write versus Type B's 1,500+ MB/s. For recovery, the smaller pin count actually makes Type A slightly easier to handle on the bench, but the cards themselves are more expensive and harder to source for testing.
Sony Card Error Messages Decoded
Sony bodies throw a smaller set of error messages than Canon, but they're often less specific about what actually went wrong.
| Sony Message | Likely Cause | Recovery Implication |
|---|---|---|
| Cannot use memory card. Format? | File-system or underlying storage problem | Do not format; preserve the card and assess read stability |
| Cannot read memory card | Connection, controller, firmware, or NAND problem | Identify the card type and supported recovery path |
| Memory card error. Reinsert | Intermittent contact | Bent pin, debris in slot. Don't keep reseating. |
| Recording could not be completed | Write failure mid-clip | Last clip may be partial. |
| Cannot record movies on this memory card | Card speed insufficient or wrong type | Not a corruption, but using wrong card. Settings mismatch. |
| Error C:32:XX or C:13:XX | Internal camera fault | Camera-side issue, not card. Service the body, test card separately. |
The most dangerous prompt is "Cannot use memory card. Format?" Sony's wording almost begs you to tap "Yes." Don't. That single tap rewrites the entire file allocation table and significantly reduces recovery surface area. Eject the card and walk away from the camera.
How Sony ARW Files Are Structured
Sony's ARW (Alpha Raw) format has been used since the original A100 in 2006 and has evolved across several versions. Modern ARW files from the A1, A7 IV, A9 III, and FX bodies use ARW 2.3 or 4.0, which are based on the TIFF/EP standard with Sony-specific extensions. From a recovery standpoint, ARW is a friendly format because it has a recognizable header pattern.
Every ARW file starts with one of two TIFF magic byte sequences (4D 4D for big-endian or 49 49 for little-endian) followed by the TIFF version marker. Sony then embeds its proprietary tags within the TIFF structure.
The complication: Sony's lossless compressed ARW format produces files that are larger and structured differently than the standard compressed ARW. The A1 in particular can produce ARW files anywhere from 50 MB (compressed) to 130 MB (lossless compressed) for a single frame. That size variability means the carver has to be smarter than a simple "find the header, count bytes, save the file" approach. We use a custom tool that parses each ARW's internal length tags to determine where one file ends and the next begins.
Recovering 8K Video: Why It's Different
Sony's A1, FX3, FX6, and FX9 record video in formats like XAVC HS (HEVC), XAVC S-I (intra-frame), and XAVC HS 4K 120p. These files are huge. A single minute of A1 8K 30p XAVC HS is roughly 5 to 6 GB. A 30 minute clip from an FX3 in 4K 120p can hit 60 GB. When a CFexpress card fails during a long video record, the file size makes recovery harder for two reasons.
First, large files are more likely to be fragmented across the card. SD and CFexpress cards write sequentially when possible, but as a card fills, the controller starts using non-contiguous blocks. A 60 GB clip might end up in 200+ fragments scattered across the NAND. Recovery means reassembling those fragments in the right order, which requires the file system metadata or a very smart reconstruction algorithm.
Second, large video files are more vulnerable to mid-write corruption.
For ARW raw still files, fragmentation is rarely an issue because individual files are small enough to fit in contiguous blocks. For 8K video, fragmentation is the default. That's why video recovery generally costs more than photo recovery when both come from the same card.
Why Sony Cards Fail in the Field
We assess failed Sony cards. The causes are consistent.
1. Pulled or Powered Down Mid-Write
Same as every other camera platform. Sony's bigger buffers (the A1 has nearly 200 frames of buffer for compressed RAW) mean the card can keep writing for 30+ seconds after you stop shooting. The blinking access light is sacred. Don't eject. Don't power off. Don't change the battery. Wait.
2. Heat Cycling From 8K and 4K 120p Recording
The A1 and FX3 generate substantial heat during long 8K record sessions, even with active cooling. CFexpress Type A cards sit directly inside that hot camera body. NAND flash bit error rates increase exponentially with temperature. A card that's been at 65 degrees Celsius for two hours of record is far more likely to throw an error than the same card running short bursts with cooldowns between.
3. Counterfeit CFexpress Type A Cards
Sony, ProGrade, and Delkin are the only major brands selling CFexpress Type A. The smaller market means counterfeits are less common than fake SD cards, but they exist. If you bought from a small online retailer or a too-good-to-be-true Amazon listing, verify with the manufacturer.
4. UHS-II Slot B Issues
Sony's dual-slot A7 IV and A7 V bodies have a CFexpress Type A primary slot and a UHS-II SD secondary slot. The SD slot uses a different connector with a second row of pins that can collect dust or grime. Dirty contacts cause intermittent failures that look like card corruption but are actually slot issues.
5. Firmware Compatibility
Sony has shipped firmware updates that changed how the camera writes to CFexpress. Early A1 firmware had bugs that could corrupt cards under specific recording conditions. Always check that your camera is on the latest firmware via Sony's official support site. Older firmware on a new card type is a recipe for problems.
6. Wear From Heavy Use
Pro CFexpress cards rate 1,000+ TBW (terabytes written) lifespan. That sounds infinite. For a sports shooter doing 30 fps bursts of 100+ MB ARW files for 8 hours a day, the wear adds up.
What NOT to Do Right Now
- Tap "Format" on the Sony "Cannot use memory card" prompt. This is the single fastest way to destroy your recovery surface.
- Reformat the card on a computer. Same problem, different tool. The file system gets rewritten and the card is much harder to recover.
- Use Disk Utility's "First Aid" on the card. First Aid is aggressive about rewriting the file system. It's designed for working drives, not corrupted cards.
- Run a Sony-branded "card recovery" download. Sony doesn't publish a recovery tool. Anything claiming to be one is generic third-party software with a Sony logo slapped on.
- Plug the card into a Windows machine and hit "Repair this drive" when prompted. Windows aggressively repairs file systems and will hurt your recovery odds.
- Keep shooting on the card after an error. Every new write potentially overwrites data that hasn't been recovered yet.
- Send it to a camera shop's "tech guy." Most local shops run the same free software you'd run. CFexpress recovery requires lab-grade tools they don't have.
Safe Steps in the Field
You're at the venue. Card error appeared. The shoot isn't over. Here's the field protocol.
Turn the camera off. Wait for the access light to go dark and stop blinking. If the light keeps blinking for 30 seconds with the camera off, the buffer is still flushing. Don't pull the battery yet. Give it a full minute to complete.
Press the door release. Slide the card out. Don't bend or flex the card. Put it in a card case labeled "DO NOT USE" or wrap it in tape with a note. The goal is to prevent it from getting mixed back into the rotation.
You brought spare cards (you brought spare cards, right?). Load a fresh one and keep working. The corrupted card is now a separate problem for after the shoot.
When you get back to base, do not plug the card into a card reader to "see what happened." Every mount potentially writes something (Spotlight indexing, .DS_Store files, Windows thumbs). Just leave the card alone until you have a recovery plan.
The Reader Problem (and Why Yours Probably Won't Work)
If you do decide to plug the card in to assess damage (against our recommendation), here's the issue. CFexpress Type A is rare enough that consumer card readers are often poorly designed. A bad reader can pass garbled data to the OS, which then misinterprets the card as more corrupted than it actually is.
For Type A cards we trust Sony's own MRW-G2 reader, ProGrade Digital's Type A reader, and Delkin's CFexpress Type A reader. Generic "all in one" card readers often have flaky CFexpress implementations. If you only have a generic reader and your card is throwing errors, you may be seeing reader-induced errors on top of (or instead of) card errors.
Inside the Lab: How We Image a Failing CFexpress Card
Here's roughly what happens when a corrupted Sony CFexpress card arrives at MDrepairs.
Phase 1: Visual Inspection
We start with a physical check under magnification. Bent pins, contact corrosion, card body cracks, signs of liquid intrusion, evidence of heat damage. The visual phase tells us whether this is a logical recovery (file system corruption) or a physical recovery (chip-level work).
Phase 2: Sector-by-Sector Imaging
If the card is detectable, we image it bit-for-bit using a validated CFexpress reader connected to a forensic workstation. The image goes to a clean drive. The original card sits in a static-safe drawer untouched. Every recovery attempt from here on uses the clone, never the original. This is non-negotiable.
Phase 3: File System Analysis
We analyze the file system structures on the clone. CFexpress cards typically use exFAT. If the FAT and directory entries are mostly intact, we manually repair them and mount the clone as a working file system. This recovers files with their original names and timestamps. If the structures are too damaged, we move to carving.
Phase 4: Raw Carving for ARW and Video
Our carver scans the clone for ARW (TIFF) headers and XAVC video markers. Each found file gets validated by parsing its internal length tags and checking that the data structure is complete. Files with truncated tails get flagged for video repair (described next). The recovered files don't have original filenames at this point but the metadata embedded in each ARW or video file usually contains the original timestamp and camera body.
Phase 5: Video Repair for Partial Clips
Some interrupted recordings can be repaired using surviving metadata and a compatible reference clip. This cannot recreate video frames or audio data that were never written, overwritten, or unreadable. The recovered clip must be checked for playable content; a header alone is not a complete recovery.
Phase 6: Model-Specific Hardware Recovery Limits
CFexpress is a PCIe/NVMe storage device. It is not automatically recoverable by removing NAND with an SD-card reader workflow. We assess the original electronics, controller/firmware support, NAND readability, and encryption. Independent chip-off is not a general fallback. Our chip-off guide explains the distinction.
Phase 7: Verification and Delivery
Every recovered file gets opened in a verification rig. ARW files get opened in Sony's Imaging Edge and Adobe Camera Raw. Video files get opened in DaVinci Resolve and Final Cut. We verify the embedded JPEG previews on raws and we play through every video clip to check for corruption. The client gets a SSD or USB drive with all recovered files plus a written report.
Dual Slot Behavior on Sony Bodies
Sony bodies with two card slots can be configured to record to both simultaneously, switch automatically, separate stills from video, or write proxies to the second slot. The configuration matters when one card fails.
- Simultaneous record: stills go to both slots. The fail-safe setting. If one card dies, the other has everything.
- Switch automatically: overflow from card 1 to card 2. Not a backup. Just extra capacity.
- Separate RAW and JPEG: RAW to one card, JPEG to the other. Partial backup. JPEGs survive but raw work is gone.
- Separate stills and movies: photos and video go to different cards. No cross-backup at all.
- Proxy to second slot (FX3, FX6, FX9): low-res proxy on the SD card. Useful for client review but not a full backup of the master.
Recovery Cost
CFexpress work needs compatible interface hardware and support for the actual fault. PC-3000 SSD firmware access differs from PC-3000 Flash raw-NAND reconstruction. Cost depends on the diagnosed work and validation, not simply on a card being labeled professional.
| Failure Type | Typical Range | Why |
|---|---|---|
| File system corruption (exFAT damage) | From $299 | Logical repair plus ARW carving. Standard recovery estimate: 4–6 weeks; may vary by case. |
| Mid-write video failure with partial clips | From $299 | Carving plus video repair. Header stitching for truncated clips. |
| Card not detected by any reader | Quoted after assessment | Check hardware and model-specific PCIe/NVMe recovery support |
| Physical card damage | Quoted after assessment | Preserve original components; feasibility depends on the damage |
| Water or heat damage | $299 to $2,000 | Clean, dry, evaluate. Then proceed with appropriate method. |
| Controller or encryption path irretrievable | May be unrecoverable | Raw NAND extraction is not a guaranteed fallback |
The $100 diagnostic counts toward a successful recovery and is non-refundable once diagnostics begin. Donor drives or replacement parts you approve are non-refundable once ordered, even if recovery fails. You approve an estimate before recovery work starts. Pricing overview here.
How Pros Prevent This
Format in the Camera Before Every Shoot
Don't reformat on a computer. Don't reuse a half-full card across shoots. In-camera format gives the Sony body a clean exFAT structure tuned for that camera's write patterns.
Buy Only From Authorized Dealers
B&H, Adorama, direct from Sony, ProGrade, or Delkin. Avoid eBay, Facebook Marketplace, and third-party Amazon sellers. The CFexpress Type A market has fewer counterfeits than the SD market, but they exist.
Use Simultaneous Record on Paid Shoots
Set the menu to "Simultaneous record" for stills. Yes, your total capacity halves. Buy more cards. The math always favors more capacity over reshoots.
Monitor Card Temperature on Long Video Records
The FX3, FX6, and A1 have menu options to display card temperature during recording. If a card hits 75 degrees Celsius, pause and let it cool. The card recovers in 5 minutes. The shoot you'd lose if it fails is hours.
Retire Cards on a Schedule
CFexpress Type A every 3 years for heavy use, 4 to 5 years for moderate use. UHS-II SD every 2 to 3 years for heavy use. Retired cards become home use or backup. Working cards stay working because they rotate out before they wear.
Watch the Access Light Religiously
The access light is the most important indicator on the body. Never eject, never power off, never pull a battery while it's blinking. Sony's larger buffer means writes can continue 30+ seconds after you stop shooting.
Don't Cheap Out on Card Readers
If you're plugging cards into a workstation regularly, buy a quality CFexpress Type A reader. Sony's MRW-G2, ProGrade Digital's reader, or Delkin's reader. Cheap generic readers can corrupt cards over time, especially during forced ejects.
Sony Models We Recover
| Model | Card Slots | Notes |
|---|---|---|
| Sony A1 | CFexpress Type A + UHS-II SD (both slots accept both) | Flagship body. |
| Sony A1 II | CFexpress Type A + UHS-II SD | Same dual-purpose slot design. |
| Sony A9 III | CFexpress Type A + UHS-II SD | Global shutter body. Heavy burst use wears cards fast. |
| Sony A7 IV | CFexpress Type A + UHS-II SD | Hybrid stills/video body. |
| Sony A7 V | CFexpress Type A + UHS-II SD | Same architecture as A7 IV with slot improvements. |
| Sony A7S III | CFexpress Type A + UHS-II SD | Low-light video specialist. |
| Sony FX3 | CFexpress Type A + UHS-II SD | Cinema line. Long 4K records stress cards. |
| Sony FX30 | CFexpress Type A + UHS-II SD | APS-C cinema. Same recovery approach as FX3. |
| Sony FX6 | CFexpress Type A + UHS-II SD | Pro cinema. Higher bitrate codecs increase write stress. |
| Sony FX9 | XQD / CFexpress Type B compatible | Older cinema body. XQD and Type B require different lab tools. |
| Sony FS7 II | XQD legacy | Older broadcast body. We still handle XQD recovery. |
If your Sony body isn't listed but uses CFexpress Type A, Type B, UHS-II SD, or XQD, call us anyway.
FAQ
Can ARW files really be recovered from a CFexpress card that says "Cannot use memory card"?
Sometimes. A format prompt does not prove the damage is purely logical. If sectors remain readable, file-system analysis and suitable file carving may recover ARW images. Unreadable data, encryption, overwritten files, and fragmentation can limit the result.
What about 8K video files from the A1 or FX3?
Some clips can be recovered or repaired, depending on how much of their data and structure survives. Reference-file repair does not recreate missing frames. We validate the recovered footage rather than promise a fixed percentage.
Should I let Sony's camera format the card when it asks?
No. The format wipes the file allocation table and significantly reduces what a lab can recover. Eject the card, label it, and don't touch it until you've talked to a recovery lab.
Is CFexpress Type A really the same as Type B for recovery?
No. Type A uses a single PCIe lane and a different connector. Type B uses two PCIe lanes and a larger form factor. The lab tools, readers, and donor cards differ between formats. We handle both, but it's not the same workflow.
Can I just buy a CFexpress reader and try to recover it myself?
Maybe, if the card is logically corrupted but still detectable. Make a bit-for-bit clone first using dd or HDDRawCopy, then run recovery software against the clone, never the original.
How fast can you turn around a Sony CFexpress recovery?
Timing depends on the failure, reading stability, and footage reconstruction. Obtain an estimate after assessment. Rush availability concerns assessment start, not guaranteed recovery completion.
What if I already formatted the card by accident?
Quick formats only rewrite the file system header, leaving most of the data physically intact on flash. Full formats overwrite everything and are much harder. Tell us if you formatted, and which type, so we can plan accordingly.
Do you handle other camera brands too?
Yes. We recover Canon CR3, Nikon NEF, Fujifilm RAF, Panasonic RW2, Olympus ORF, and every other raw format. Each format has its own approach. Our DSLR memory card recovery guide covers cross-brand specifics.
Do you ship to clients outside New Jersey?
Yes. Prepaid shipping label, signed-for delivery. Mail-in process details here.
What's the difference between consumer recovery software and what a lab does?
Software can help with logical damage on readable storage. A lab may additionally address repairable hardware or supported firmware faults, then extract and validate the surviving data. Some controller, NAND, and encryption failures remain unrecoverable.
How do I know if it's a card problem or a camera problem?
Try the card in a different camera body of the same line (borrow from a friend if you can). Try a different card in your camera body. If the card fails in two bodies, it's the card. If different cards fail in your body, it's the camera's slot or controller. We can diagnose either way.
MDrepairs is an independent data recovery lab serving professional photographers, videographers, and cinematographers nationwide via mail-in service. We're not affiliated with Sony. Our specialty is recovering ARW raw files and XAVC video from corrupted or failed CFexpress Type A, CFexpress Type B, XQD, and UHS-II SD cards.
Get help with data recovery
Bring your device to our Lincroft lab during opening hours, or mail it in.
How to mail your deviceThe $100 diagnostic is non-refundable once diagnostics start, and donor drives or replacement parts you approve are non-refundable once ordered, even if recovery fails.
Published by MDrepairs
MDrepairs is a data recovery and electronics repair lab in Lincroft, New Jersey. Our founder and lead technician Joseph Montanti films real cases for our YouTube channel, showing tools, repair steps and recovery outcomes.
Keep reading
- USB “Device Descriptor Request Failed”: What It Means for a Flash Drive
- USB Says “Please Insert a Disk” or “No Media”: Can You Recover the Files?
- SD Card Write Protected? Fixes Beyond the Switch
